(1) 為使熔斷器能更可靠、的運行，除按規程要求嚴格地選擇正規廠家生產的合格產品及配件(包括熔件等)外，在運行維護管理中應特別注意以下事項： ①熔斷器具額定電流與熔體及負荷電流值是否匹配合適，若配合不當必須進行調整。 ②熔斷器的每次操作須仔細認真，不可粗心大意，特別是合閘操作，必須使動、靜觸頭接觸良好。 ③熔管內必須使用標準熔體，禁止用銅絲鋁絲代替熔體，更不準用銅絲、鋁絲及鐵絲將觸頭綁扎住使用。 ④對新安裝或更換的熔斷器，要嚴格驗收工序，必須滿足規程質量要求，熔管安裝角度達到25°左右的傾下角。 ⑤熔體熔斷后應更換新的同規格熔體，不可將熔斷后的熔體聯結起來再裝入熔管繼續使用。 ⑥應定期對熔斷器進行巡視，每月不少于一次夜間巡視，查看有無放電火花和接觸不良現象，有放電，會伴有嘶嘶的響聲，要盡早安排處理。 (2) 在春檢停電檢修時應對熔斷器做如下內容的檢查： ①靜、動觸頭接觸是否吻合，緊密完好，有否燒傷痕跡。 ②熔斷器轉動部位是否靈活，有否銹蝕、轉動不靈等異常，零部件是否損壞、彈簧有否銹蝕。 ③熔體本身有否受到損傷，經長期通電后有無發熱伸長過多變得松弛無力。 ④熔管經多次動作管內產氣用消弧管是否燒傷及日曬雨淋后是否損傷變形、長度是否縮短。 ⑤清掃絕緣子并檢查有無損傷、裂紋或放電痕跡，拆開上、下引線后，用2500V搖表測試絕緣電阻應大于300MΩ。 ⑥檢查熔斷器上下連接引線有無松動、放電、過熱現象。 對上述項目檢查出的缺陷一定要檢修處理。