• 
• 
• 
• 
• 

云海旭金屬材料有限公司

鋼筋套筒如何在低溫條件下灌漿施工？灌漿區域保溫攪拌機保溫：用纖維保溫氈包裹機身并封口；灌漿罐保溫：用纖維保溫氈包裹機身及頂蓋；注漿管路保溫：用纖維保溫氈將管路包裹，降低灌漿料在灌漿管路內散失熱量，保證灌漿入套筒溫度不低于5℃，延長灌漿料的工作時間；攪拌漿料的用水溫度：攪拌漿料的用水溫度控制在0℃～10℃之間，以保證灌漿料的溫度；機械灌漿采用可調機械壓力灌漿工藝，通過控制機械電機速度來控制灌漿過程漿體流速，控制依據為灌漿過程中本灌漿腔內已經封堵的灌漿孔或排漿孔的橡膠塞能耐住低壓灌漿壓力不脫落為宜，如果出現脫落則立即塞堵并調節壓力。灌漿腔保壓排漿孔漿體成柱狀逐一排出，采用橡皮塞逐一封堵，所有灌漿套筒的排漿孔均排出漿體并封堵后，調低灌漿設備的壓力，開始保壓，保壓30秒。

鋼筋連接:①連接鋼筋時，鋼筋規格和連接套的規格一致，鋼筋螺紋的型式、螺距、螺紋外經應與連接套匹配。并確保鋼筋連接套的絲扣干凈、完好無損。②連接鋼筋時應對準軸線將鋼筋擰入連接套。③接頭拼接完成后，應使兩個絲頭在套筒中央位置互相頂緊，套筒每端不得有一扣以上的完整絲扣外露，加長型接頭的外露扣數不受限制，但有明顯標記，以檢查進入套筒的絲頭長度是否滿足要求3）鋼筋套筒質量要求:①連接套表面無裂紋，螺牙飽滿，無其他缺陷。②牙型規格檢查合格，用直螺紋塞規檢查尺寸精度。③各種型號和規格的連接套外表面，必須有明顯的鋼筋級別和直徑。④連接套兩端頭的孔必須用塑料蓋封上，以保持內部潔凈，干凈防銹。

鋼筋套筒工程開工前施工技術人員要了解設計文件規定的鋼筋接頭性能等級應由該技術提供單位提交有效的型式檢驗報告.型式檢驗報告必須包括連接套長度、鋼筋連接套筒外徑、內徑、錐度、扭緊力矩值、牙形角平分線垂直于錐面等參數.(3)鋼筋連接工程開始前及施工過程中應對每批進場鋼筋進行工藝檢驗工藝檢驗合格后方可在工程上進行鋼筋機械連接操作.(4)要作好技術交底工作及時填寫接頭質量檢查記錄.(5)直螺紋的外觀檢驗隨機抽取同規格接頭數的10%應滿足鋼筋與鋼筋直螺紋連接套筒連接套的規格一致接頭外露絲扣不超過三扣其它要求與錐螺紋的外觀檢驗基本相同.鋼筋連接對接頭有特殊要求的結構應按設計文件注明的檢驗項目要求作相應的檢驗.