埋刮板輸送機產品的安裝與維護:埋刮板輸送機的安裝需要進行以下工作：1)定位:首先定出機頭和機尾的位置，然后再定出刮板輸送機的中心線。2)鋪設中間槽:根據定出的輸送機中心線，鋪設中間槽。如采用非金屬槽箱，則中間槽鋪砌磚和水泥預制板，再粘結鑄石襯板。鑄石襯板鋪設時，要注意平直，接縫盡量少，縱向縫隙要錯開，防止工作時將縫隙磨成溝。輸送機表面鋪設需要平直，如輸送機平面內有過大的彎曲，勢必導致兩條鏈受力不均勻，加速鏈子與槽壁鑄石之間的磨損，甚至卡鏈。各段槽體搭接應平整無臺階。由于槽體本身結構限制，相鄰中間槽在垂直方向偏轉不應過大。若輸送機鋪設不平直，運輸功耗將會增加。機道上的積煤或雜物應掃除干凈。3)安裝機頭和機尾:機頭和機尾應留有一定空間，便于維護及檢修。鏈輪中心線要與輸送機中心線垂直，并保證水平。4)裝刮板鏈:刮板鏈在安裝前，應預先連接好，刮板均勻地分布在鏈條中。除渣機配件